(800) 853-2651
SHOP NOW

Putting back together controller 49 IH-H...Help...

R

Raner

Member
First of all thanks to all who have been helping on my post...
Ok guys got the seal in...and the shaft is back on...
When I pulled the controller apart all the control check valves, springs, two big ball check valve and a small one, one big spring were all just laying all over the place. Need to figure where everything... goes correctly...Going to check the brake down link Anthony posted see if I can find where everything goes...Raner
http://partstore.caseih.com/us/parts-search.html#epc::mr59088
 
If you disassembled it from the outside the parts diagram should work for putting it back together. I have never cracked one open so if it's internal I'm not sure...let us know how you made out, I'm going to be doing my oil seals soon on my M and I might have to pick your brain soon lol ~Anthony
 
Hello again...
Could not find the information I needed on the link...
I took a picture of the parts I need info on, Maybe someone can
tell me where his stuff goes...

Need info on this!

Info picture One

Info picture Two

Info picture Three


Looks to me like the big ball check valves go with the two piston actuators, and the small ball-spring-and button go together but have no clue where the cups go...But I could be way out on left field as to where the stuff goes...
If some one has a stigmatic for the controller can you take a picture and post it, That would be great ...Or if you can walk me threw it that will be good also...Thanks Raner
 
Hi Antony...
The problem I have is when took the controller apart the darn thing came apart before I could see where every was...LOL..
Pulled out the complete unit...this thing is heavy, had to use my floor jack to get it out...
Some one had been in there...they double gasket the base of the pump and did not put a gasket on the top of the pump where it meets with the top section...beat the hell out of the seal and...Has to pull the shaft from the gear with a press to get to the seal...then had to repair and polish some bad nicks to get the gear back on...when in fairly easy...
When you get ready to do yours just email me at [email protected]
I help you in anyway I can...Raner
 
I have several belly pumps around that came out of parts Hs and I
could send you one, the pump part has to ship separately from the
reservoir due to weight but if all you need is the pump they are not
too heavy to send. I am in northern NY, if you would like one just
let me know your zip code and I can check to see the postage cost.
Zach
 
Thanks Zach...
I'll keep it in mind. If mine leaks, I'll get one from you...
I am in Corpus Christi, Tx, Zip Code is 78413...
My email is [email protected]...
I need to figure out where to put back the check valves and I think I'll be alright...
I looked to download a repair manual but could not find one.
Every one I found has to be shipped and my wife is going to kill be because the tractor is apart in drive way...LOL...
Thanks again for the offer and will see how it goes...
If you would just send me an email so I can have yours in case I have to contact you on the pump...Raner
 
Ok guys got the belly pump unit installed and everything seems to be working just fine and no leaks...Ran it for about 30 minutes...The reason I could not figure it out is because I was missing a spring for one of the big ball control valve...I found one in my tool box that pretty darn close to the one I had and it worked fine...
Thanks to all of you that helped me out on my post...
I am EXPERT ON FARMALL - H BELLY PUMPS...LOL...Raner...
 
There are no gaskets as such in the pump assembly. They are shims to set the end clearance of the gears to the end plates. That is way they are all on the same end.

early pumps were lower pressure and did not have any provision for setting the clearance so they have no shims.
 
Hello Owen...
Mine must be considered the early one because I did not see any shims in it and I had it completely apart...
 
You must log in or register to reply here.

Similar threads

8
PLEASE HELP 49 8N Ford
Replies
18
Views
1K
Jerry9N
J
C
SOS Massey Ferguson HELP
Replies
6
Views
493
Catalpa Cat
C
V
new owner of a 620, will try to update this as we go.
2 3 4
Replies
61
Views
3K
valiant8086
V
R
Farmall 450 fast hitch hydraulic - again
Replies
15
Views
1K
RandyM
R
T
Power steering valve help
Replies
6
Views
455
Ultradog MN
Ultradog MN
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top