(800) 853-2651
SHOP NOW

706 farmall lp

C

chris cummins

Member
Hey ya'll thanks for the help last summer when trying to decide whether to buy the 1000.00 706 lp ,glad i did ,its overkill.Now i sold my deere and have decided just to fix up one tractor.I had both front ends for the deere.Does anyone know if the narrow front off a 3020 deere will fit on my wfe 706? I kept it in case it would fit ,it is complete to the tires. What size were the factory front wheels on the wfe. 15 or 16?What kind of suitcase weights would have been used on the706 in 1963? More ? To come.
 

My 3020 and daughter
a113028.jpg
 
No.The the JD front end will NOT fit the IH. A '7' would come with either 7.50x15 or a 6.00/6.50x16 front tire.IH used either a 75lb or a 100lb suitcase wt.The 100 being the most common.
 
Cute Daughter. Can't say the same about the green thing. LOL Why don't you show a pic of the 706LP? THanks Kent
 
Don't mean to hi-jack the post but it's funny i was just sittin here fixin to post a question about a 706 LP tractor with a front blade. I'm going to look at one. I beleive it is a 706 it's a wide front. I know it has a LP line leaking but not sure about any other problems.I know this isn't much information but I don't want to go in blind.What would one be worth and what should I look for? Thanks.
 
One thing I would look for is whether the Ensign regulator/vaporizor works, that is, if the engine runs normally. I have an Ensign that came on my 450 and had to use an aftermarket Reg/vap unit for the time being, there is a guy in Oklahoma that sells kits for them, but other than that, parts are very scarce for the Ensign units. Also, it wouldn't be a bad idea to get you a spray bottle and mix up some water with a little detergent to check for leaking valves on the tank, they are still available but can be annoying when you are ready to fill the tank but can't because of leakage. Hugh
 
I think your original questions have been answered, but I just wanted to let you know if you ever decide you want to get rid of the 706LP, give me a holler. I am highly interested and down here in western Ky. And I too, would be like to see a picture(s) of the tractor.
 
You must log in or register to reply here.

Similar threads

F
706 Farmall fuel cut off solenoid repair
Replies
3
Views
279
used red MN
U
R
FARMALL M LP HEAD
Replies
2
Views
422
RedMVa
R
A
Farmall 706/806 operator platform bolt locations???
Replies
3
Views
265
caterpillar guy
C
C
Low compression in farmall 706
Replies
15
Views
872
Cowboy2005
C
F
Farmall M Wide Front Attachment
Replies
1
Views
186
Janicholson
Janicholson
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top