(800) 853-2651
SHOP NOW

Hydraulic Hose Question

Our Phone System is Down!

Please use the Contact us Form

We are working to resolve the issue ASAP! Thanks for your patience!

G

Global Warmer

Member
Hello all how is everyones projects going.
I"m debating on whether to use gates rubber hose or a stainless steel braided hose.
My second question is can I plug all the hydraulic pump inlets and outlets until I add hoses and still use the tractor.

Thanks to all reply"s in advance.

TMCKEE
 
Jim/G Warmer - A clarification: It's OK to plug christmas tree valve outlets on a letter series tractor so long as the control handle is centered. But DO NOT the pump inlet/outlet ports then run the tractor!
 
Good point,I ''assumed'' only equipment hoses were being considered. And without a picture it is just question marks. Jim
 
(quoted from post at 20:38:26 03/25/13) Hello all how is everyones projects going.
I"m debating on whether to use gates rubber hose or a stainless steel braided hose.
My second question is can I plug all the hydraulic pump inlets and outlets until I add hoses and still use the tractor.

Thanks to all reply"s in advance.

TMCKEE
Click to expand...

Is this a series I or II Super H? If it has the series II timing gear driven pump, DO NOT plug the inlet and outlet pump ports. I don't know one way or the other about the belly pump on the earlier models, as I don't know the internal plumbing. You will break or burn up the timing gear driven pump on a series II, depending on how tight the intenal gears of the pump are. If they are somewhat loose, the oil left in the pump will slip by the gears and eventually get hot and burn up the pump. If the gears are tight, you will break something, probably one of the cam timing gears or the pump shaft or driving gear.

You could "loop" a hose from the inlet to the outlet and fill it with oil, but even that might tend to get hot if run a long time, bit it would be better than running it plugged.
 
You must log in or register to reply here.

Similar threads

G
Need hose that goes from hydraulic tank to hydraulic motor on 1980 Ford 445 diesel
Replies
2
Views
192
gnc23
G
E
Random hydraulic questions
Replies
2
Views
451
eod4647
E
T
MF 204 loader needs hydraulic hose repair
Replies
1
Views
321
greasyBob
G
T
Deutz =Allis D10006 hydraulic help
Replies
2
Views
310
BarnyardEngineering
BarnyardEngineering
D
Case 1030 Hydraulic Pressure-Question for John Saeli or others
Replies
5
Views
495
DRussell
D
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top