(800) 853-2651
SHOP NOW

A Farmall Moldboard plow mounting

M

Mo in NE tex

Member
here are a few pics of the plow I talked about earlier in this forum. The beam is 7" long.
One of the brackets that bolts to the rear housing is missing. Gene Bemder, does the same leaver that works the cultivator lift the plow or do I need the lift leaver that fits on the right side of the tractor by the floor board? Also, how does the front hook up. I see two mounting holes on the front bolster, but where does the rest attach? HELP!!!!!
a100690.jpg

a100691.jpg

a100692.jpg

a100693.jpg

a100694.jpg
 
Looks to me you got the rock shaft for the pneumatic lift hooked to the plow. The plow will fit on the handlift setup (I actually have both types) and I think I saw some of the handlift parts on e-bay recently. I have the lift on now for them both, but with snow plows. I will get some pics for the lifts posted.
 
My spare hand lift rockshaft doesn"t have the crank either. But the one I am using and the pneumatic lift does. Must have been a change in there.
 
My spare hand lift rockshaft doesn"t have the crank either. But the one I am using and the pneumatic lift does. Must have been a change in there.
 
I can't get the pics to upload. You will also need the lever that bolts to the clutch housing to adjust the point depth. Yours hooks up different in the front than mine does, mine hooks to the pin that holds the plow to the front bracket. I think you have an earlier one that is fixed, my front bracket has a big spring in it. Hopefully someone else can jump in.
 
Your plow is made for the exhaust lift. You need the platform mounted lever for the hand lift. Then you will need to weld a piece on the rockshaft to hook up the lever. I think i have that lever as i did sell one to a fellow in OHIO. But you do have the rest of the mounts. The crank on the rockshaft is for leveling the plow. If the rain and snow mix doesent get here tomorrow i will go look. We can work out some way to lift your plow i know i did cut one up for the spring but i will look.
 
You must log in or register to reply here.

Similar threads

G
Mounting WL-40 loader on a 706
Replies
4
Views
361
fastfarmall
F
J
Looking for a shank for moldboard plow
Replies
3
Views
234
jpi72
J
B
Snow plow mounting on Ford 4100.
Replies
8
Views
685
Leroy
L
E
Home made snow plow subframe mounting
Replies
11
Views
3K
ZehnX
Z
B
Mounting a MF 236FED to a MF235 tractor
Replies
1
Views
1K
ArleninOr
A
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top