(800) 853-2651
SHOP NOW

WD-9 Drawbars

S

sflem849

Well-known Member
Here is an update post on 9 series drawbars. We talked about how you never see the same drawbar twice on a 9 series tractor.

This is what the WD-9 book shows as correct for a 9 series with swinging drawbar attatchement.

2012-06-17_21-01-56_226.jpg


Sorry for the iffy picture. I just took a picture of the book rather than scanning it because I am lazy. :?
 
This is correct on earlier 9 series tractors. Later 9 series swing drawbars were available with a roller rather than the slide, although the slide type was probably available throughout production.

Harold H
 
Same roller as an M? Similar, but bigger would be my guess.

I think I am going to try to recreate the one in the picture. If anybody has any measurements I would appreciate it.
 
the one in this pic makes it a double strap hitch some tractors may have had a roller but then were a single strap i will have to look at our wd 9 tomorrow to see what it has may be able to get measurments for you
 
The drawbar in the picture is exactly what is on all of my WD-9"s and Super WD-9 built between 1951-1955. I have never seen a factory roller type but it sounds like they existed on some tractors. I can also get you some pictures & measurements if you still need them. WD-9"s used to be real common here in Canada and finding the drawbar parts would have been easy at one time (okay, I"m not much help am I?).
 
(quoted from post at 22:04:03 06/19/12) The drawbar in the picture is exactly what is on all of my WD-9"s and Super WD-9 built between 1951-1955. I have never seen a factory roller type but it sounds like they existed on some tractors. I can also get you some pictures & measurements if you still need them. WD-9"s used to be real common here in Canada and finding the drawbar parts would have been easy at one time (okay, I"m not much help am I?).
Click to expand...

There are some parts of the country where they are as thick as Ms around here. There is no reason you need to taunt me about it. :lol:

I could use the measurements if you get a chance. Thanks!
 
You must log in or register to reply here.

Similar threads

D
Cutaway pictures
Replies
6
Views
600
Hobo,NC
Hobo,NC
D
Allis model D grader refurbishment
Replies
7
Views
503
wore out
wore out
L
Anyone else have a Problem with YT sending wrong parts?
Replies
7
Views
452
LarryMaine
L
G
JD R and WD-9
Replies
12
Views
1K
mrslesq
M
T
Case wheel weights DONT fit. G1340 530CK 430 530 400B 58
Replies
0
Views
257
TFLundyB275
T
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top