(800) 853-2651
SHOP NOW

Where to get injector pump parts?

C

CenTex Farmall

Well-known Member
Where's the best place to find seals for the 400D I've been working on? I need the seal for the lift pump. Type B injector pump.

I haven't had luck finding part numbers on the IH website. Anyone know if IH still has seals for these.
 
Earnie, Try, Pervis Bearing or another Bearing Supply House, if they don't have it,,, I will bet you will need to contact a local Dsl Injection Repair Shop and run the #s past them to get what you will need. Hopefully they won't be Horses Buts about it since you are not letting them do the work!
Latter,
John A.
 
(quoted from post at 13:15:52 05/28/12) Earnie, Try, Pervis Bearing or another Bearing Supply House, if they don't have it,,, I will bet you will need to contact a local Dsl Injection Repair Shop and run the #s past them to get what you will need. Hopefully they won't be Horses Buts about it since you are not letting them do the work!
Latter,
John A.
Click to expand...

If that fails, Central Fuel in Iowa will mail you one. Think they sell parts as well as do the repairs. They get some of the stuff for these pumps custom made.
 
Messicks show they have one 266594R91 in stock, but don't have a big one. Just under $60.00. Probably over $70 shipped to you.
Original numbers for seal were the above # or 266595R91.
 
Thanks!

That part number is the missing link. Didn't have any luck with various forum searches or the Case/IH parts page.
 
I'll write that name in my book too! Hopefully I can get it going with just a good clean out of the fuel system. I want to go ahead and change that seal while I have it apart. It was obvious that the oil in the pump sump had at least some level of dilution.
 
(quoted from post at 22:01:19 05/28/12) I'll write that name in my book too! Hopefully I can get it going with just a good clean out of the fuel system. I want to go ahead and change that seal while I have it apart. It was obvious that the oil in the pump sump had at least some level of dilution.
Click to expand...

I don't want to be pushy, but it wouldn't hurt to post the crossed SKF/CR number when you find out. :D
 
(quoted from post at 05:27:58 05/29/12)
(quoted from post at 22:01:19 05/28/12) I'll write that name in my book too! Hopefully I can get it going with just a good clean out of the fuel system. I want to go ahead and change that seal while I have it apart. It was obvious that the oil in the pump sump had at least some level of dilution.
Click to expand...

I don't want to be pushy, but it wouldn't hurt to post the crossed SKF/CR number when you find out. :D
Click to expand...

That is not likely as the seal is a custom part for IH. However miracles do happen and if somebody finds a cross that works, there is a lot of people wanting that information.
 
You must log in or register to reply here.

Similar threads

F
Need advice on the fuel line going to pump.
Replies
3
Views
245
rustred
rustred
S
Need to confirm parts
Replies
6
Views
289
BarnyardEngineering
BarnyardEngineering
T
1939 UTS Water-pump issues & parts
Replies
10
Views
376
Duey C
D
Z
MF 265 No Fuel to Injectors
Replies
6
Views
330
zcronk
Z
T
300u hydraulic actuator parts
Replies
4
Views
302
tarment10
T
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top