(800) 853-2651
SHOP NOW

Clutch Pedal Shaft Bushing.Where to get it????

Our Phone System is Down!

Please use the Contact us Form

We are working to resolve the issue ASAP! Thanks for your patience!

M

mike1972chev

Well-known Member
Yea,Me again! :)

Can I buy the clutch pedal bushing at IH/CNH or is there a BETTER source for it???

1953 Super M Farmall(But you ALREADY knew that! lol)
 
To the best of my knowledge, and after looking at the parts list there isn't one. The metal of the pedal (excuse the pun like words) Is in contact with the brake pedal cross shaft. To repair it is rebushed locally to the shaft size. If the shaft is worn, the solutions are to turn the shaft down to a just less than the wear, then ream the new fabricated bushing to .0015 to .002" bigger.
The other way is to remove the shaft and have it welded back to size and turned/ground to original diameter, then use a bushing to the same spec as above. Be sure to drill for the grease Zerk. Jim
 
buy a couple wrist pin bushings for the diesel 282 pistons and have the machine shop ream the pedal and install the bushing.
 
I take the shaft and the pedal to a machine shop and he makes a new shaft and puts in the right bushing.
 
You can buy the shaft from S teiners, OEM, etc as well. IIRC it is a $60 part. My machine shop will buy the shaft when they are busy or make it when they are slow/not ordering other stuff. Think about the time it takes to make it and it is probably a wash. The then bush the pedals to the correct size.

If you want to half do the job you can just buy the new shaft. That should take out half your slop (in theory)

On the side the 1941 H I just bought has about 1/8" movement in the pedal!!! The drawbar also shows only SLIGHT wear. The tractor must have never been used.
 
I had the clutch pedal repaired on my Farmall 400, I provided a bushing with an ID of 1", OD 1.25" and the appropriate length. The machine shop bored the pedal to 1.25", installed the bushing and then bored the bushing to 1.128" to fit the shaft.
 
You must log in or register to reply here.

Similar threads

M
806 Clutch pedal shaft.
Replies
5
Views
402
caterpillar guy
C
C
Super C Clutch Adjustments
Replies
16
Views
342
cdd
C
M
MF35 Clutch Pedal Dropped - Can't shift
Replies
5
Views
188
damn1981
D
W
2N Clutch pedal modification
Replies
3
Views
412
boler76
B
G
Replace clutch assembly on 8n
Replies
15
Views
623
Myold48-49#
M
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top