(800) 853-2651
SHOP NOW

464 Bumper

S

SouthernFarmall

Member
I am looking for a front bumper for my 464 because mine got torn up, as you can see. Whenever I call a company and ask for a 464 bumper, they send me pictures that are different from what I have. I am starting to wonder if my bumper is actually off a different tractor. My bumper attaches to the front of the tractor with 2 bolts and has a full width bracket running behind the actual bumper with a support bar in the middle. Does anyone know if this is the correct bumper for this tractor and, if not, what tractor it was for? Also, where would be the best place to find a new one?

SF
a64116.jpg

a64115.jpg

a64114.jpg

a64113.jpg
 
Other than needing sandblasting, maby a bit of welding, and new paint I don't see that much wrong with that bumper. Remove it from the tractor, sandblast, repair, and repaint and it will be good as new! In other words nothing wrong that can't be fixed. Use it and enjoy!! Armand P.S. Be sure to show us the after pictures!
 
I also think that it can be repaired to be good (or better) than new. Take it to a blacksmith, or welding repair shop and get a few bids. Also ask at a trade school. If you are in central MN, I could have students straighten and weld it for free as an assignment. Jim
 
I asked a local welder/blacksmith/engine rebuilder to take apart and re-weld a big galvanized steel bracket for my tractor (MF-240) to make it into a front fender that would fit. He took a long look, said he had a better idea. Took it over to his huge many-many-ton hydraulic press, put it in, and pressed it right into the correct shape. Was done in a couple minutes. Might not work, but youmight ask around, get that bent side pressed right back into shape.
 

I'd straighten and fix that one, I'm not aware of any "factory" bumper for these tractors. It's likely a one off or low production piece and not necessarily an IH part (?)
 
Thanks for your advice! I was surprised to hear that you all thought my bumper could be fixed and still retain its strength! I got a few welders phone numbers today and I will get some quotes. Thanks again!

SF

PS: I will try to get some "after" pictures posted later on.
 
You must log in or register to reply here.

Similar threads

H
IH 424 front weights
2
Replies
25
Views
886
hoosier43fan
H
Hdonly
Building TO-20 swing-out bumper
Replies
3
Views
643
Jim L WA
J
L
BUMPER FOR A 3000 FORD
Replies
2
Views
310
Tim PloughNman Daley RIP
T
N
IH 464 fuel sender ohm range
Replies
4
Views
471
jimtrs
J
A
New (to me) 1960 Massey Ferguson 35x
Replies
4
Views
372
alfio
A
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top