(800) 853-2651
SHOP NOW

International Emblem for I-4

B

Bob in Mi.

Member
Is there only one International emblem (normally referred to as for International A) or is there a larger emblem for the I-4. According to all the research I have done the I-4 should have an International emblem rather than McCormick or McCormick deering.

The International A emblem is about 2" shorter than the McCormick or McC Deering and looks small on the I-4 grill.
 
(quoted from post at 20:18:13 12/05/11) Is there only one International emblem (normally referred to as for International A) or is there a larger emblem for the I-4. According to all the research I have done the I-4 should have an International emblem rather than McCormick or McCormick deering.

The International A emblem is about 2" shorter than the McCormick or McC Deering and looks small on the I-4 grill.
Click to expand...

The "International" grill emblem for the I-4, I-6, is the same physical size as the "McCormick", or "McCormick Deering" grill emblem for the W-4, W-6.

No one is making the correct size International emblem. I have one I found from from an ebay seller, but had to pay through the nose to get it.
 
I had been looking for one for my I-6 for several years. Found one this year from a vendor at our local show. It was made from steel, not aluminum as are the newer ones. It was original rusty. I had to blast clean and paint it myself. I paid $55 for it and the vendor would not negotiate.
 
(quoted from post at 17:47:59 12/06/11) I had been looking for one for my I-6 for several years. Found one this year from a vendor at our local show. It was made from steel, not aluminum as are the newer ones. It was original rusty. I had to blast clean and paint it myself. I paid $55 for it and the vendor would not negotiate.
Click to expand...

I found the aluminum version at a swap meet several years ago. If I remember right, that vendor was asking about that same price, wouldn't negotiate, except that particular emblem was bent, twisted, and slightly torn in a couple of places. I walked away.
 
You must log in or register to reply here.

Similar threads

N
1066 engine overhaul
2
Replies
20
Views
1K
Janicholson
Janicholson
P
international 300 utility tractor pto seal
Replies
4
Views
323
D Slater
D
Horsez2
New to Hay Baling and need advice!
2
Replies
29
Views
2K
ajl
A
M
Need a little Help!
Replies
3
Views
435
mk6969hthr
M
C
1953 NAA
Replies
12
Views
1K
Check Break
C
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top