(800) 853-2651
SHOP NOW

does the gasket kit here for the c have the crank seal?

S

souNdguy

Well-known Member
I see a farmall C master gasket kit here as :

Complete Gasket Set w Seals - Overhaul gasket set For Models: 130, 140, 22, 230, 240, 62, 76, 81, A, A1, AV, AV1, B, BN, C, Super A, (U-2, U-2A up to sn 22113), (330, 340, 404 with C135). Replaces FS3150. (Part No: OGS113)

does this contain the:

Crank Seal, Front - For Models: 100, 130, 140, 200, 22, 230, 240, 62, 76, 81, A, A1, AV, AV1, B, BN, C, SUPER A, SUPER A SN 255418-310299, SUPER A SN 310300>, SUPER AV, SUPER AV SN 255418-310299, SUPER AV SN 310300>, SUPER C, U-2 SN <22113, U-2A SN <22113. (Part No: 389407R92)

and does it have the front timing cover gasket?

also, has anyone purchased the op manual or parts manual from here:

C Parts Manual 182 Pages (Part No: IH-P-C) $33.95
Ships within 1-2
business days.


C Operators Manual 87 Pages (Part No: IH-O-C) $29.95


thanks

soundguy
 
Soundguy, You can look up part #"s on case IH
There is a break down of most tractors. Than you can Have NAPA cross the # to see if they can get it. If not most case IH dealers will ship it to you no mater where you are. If YT does not list it sepratly you can still call them to see if you can buy just the front seal not the hole kit. oldiron29
 
Take a good look at the hub on the damper pulley to make sure there's no groove worn into the hub.
If it has a groove you need a speedi-sleeve to cover that surface. Napa should have the speedi-sleeve and seal.

To answer your question I think a complete gasket set should include the items you mentioned. Hal
 
Buy your manuals from www.external_link, the pages and diagrams are clearer. They are digital copies of the original IH manuals. Jensales sold by this site claim that they have switched to digital, which would make their manuals easier to read. However they toss in a lot of advertising and the manuals are bound differently than the original IH/binder books ones. If the gasket kit is the same one as the ones with their engine kits, which I have purchased EVERY seal will be there. If all you need is the front seal and gasket, get the numbers from www.caseIH.com and purchase from the nearest CIH dealer, or order from www.external_link, you will get them in 3-4 days. NAPA, etc can cross the numbers, they will likely have to order also.
 
Here's the link to the parts lookup. You need to enter it as "Farmall C" as "C" alone doesn't bring up the parts cat.
CIH parts
 
at a minimum I know I need a manifold gasket, timing cover gasket and front seal. figured if they ae all 9-10$ items.. it might be just as easy to buy the 50$ master kit. but will sure look up the #'s and see what napa says.

unfortunately no CIH dealer within many, many cities of me... many hours drive :(

Also need a pto seal.. am sure that is seperate... bt maybee napa has it as well.

wonder if it can be changed from t he outside. almost looks like it can.

thanks
 
Yes, you can pull the PTO seal or in my case dig it out. I usually make a small hole and use a slide puller first. Works sometimes, sometimes not. Hard to get seals from CaseIH for less than $20 up, they are usually 30-50% higher than anyone else.
 
yep, i've got a slide hammer with a 'screw' end for pulling seals or body pannel dents. I've pulled some external shaft seals before.. this one LOOKED like you could do it. but again.. new with these reds.. figured I'd ask before trying just in case.

thanks for the help.

appreciate it.

soundguy
 
You must log in or register to reply here.

Similar threads

S
C123 9 vs 14 bolt discussion
Replies
7
Views
6K
ghenges
G
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top