(800) 853-2651
SHOP NOW

Can I add a pto to a 2606?

Our Phone System is Down!

Please use the Contact us Form

We are working to resolve the issue ASAP! Thanks for your patience!

B

bc

Well-known Member
I just got the backhoe removed from my 2606. As soon as I get it to run, I'll remove the IH 3000 loader so I can do some engine work.

Anyway I was just wondering about how much and how easy/difficult would it be to add a pto unit assuming I could find one at a reasonable price?It has a 5 speed with forward/reverser lever.

I'd probably have to weld some type of draw bar on it and maybe add a cylinder. I'd like to pull a mower and maybe a haybine and baler. And I don't really want another tractor around that needs repairs and tires and stuff. Thanks.
 
We need the letter suffixes on the serial number to determine whether transmission driven PTO or independent PTO.

Which ever one fits, you can probably source the parts from a 460/504/606. You can figure that out by going to the CaseIH on-line parts book. There is a remote chance that parts from a 300/350 will work but they are likely to run at the wrong speed.

Anyway, don't weld anything to the tractor. In fact, get another tractor. Life's too short to start reconfiguring a shuttle shift 2606. Money will add up too.
 
"IMHO",the 606 is junk-not worth the effort.There were not many built so used parts will at best difficult to find.You will probally end up replaceing mostparts from the pressure plate on back.For what you will spend on parts(not counting your labor),you can buy a good 460/560(or better) for less money.But iff thats what you really want to do,"go fot it!"
 
Thanks. I just thought if I could pick one up for 500 bux more or less then it might be worth it.
 
You can get the PTO unit for that. The issue is that the PTO drive system might not be in the tractor at all. The shuttle trans may not have provision for the drive components and shafts necessary to make it feasable.
Checking the web site might get you there, a service manual for the tractor with shuttle trans will for sure address the issue. Jim
 
You must log in or register to reply here.

Similar threads

B
2606 Radiator leaks
2
Replies
31
Views
825
Janicholson
Janicholson
B
2606 carb doesn't fit right
2 3
Replies
42
Views
937
bc
B
T
Weak PTO on IH 300 Utility
Replies
4
Views
249
MARK ROBKE
M
B
want to add 3 point backhoe to Ford 4500
Replies
4
Views
522
paul
P
Kcavery2019
Power beyond Plug
Replies
13
Views
568
jean claude marleau
J
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top