(800) 853-2651
SHOP NOW

560 rod bearings

C

cory s

New User
have a 560 gas with 60 under rod bearings and was wondering if anyone knew a place to get these yet? so far everyone has told me they have been discontinued
 

0.060" under?? WOW!! Most machine shops refuse to go any smaller than 0.010" under. Do yourself, and your tractor a BIG favor and find a much better crankshaft.
 
well thanks for the help so far, but they did offer 60 under at one time and yes i know that is very odd but i am trying to save some money because there is nothing wrong with the crank. just thought someone might know of some new ones sitting on a shelf somewhere. I would never turn one to 60 either but if your machine shop wont go farther then ten you might wana send those cranks my way
 
(quoted from post at 16:12:25 01/25/11) well thanks for the help so far, but they did offer 60 under at one time and yes i know that is very odd but i am trying to save some money because there is nothing wrong with the crank. just thought someone might know of some new ones sitting on a shelf somewhere. I would never turn one to 60 either but if your machine shop wont go farther then ten you might wana send those cranks my way
Click to expand...

Any crankshaft that has been turned 0.060" undersized is NOT a good crankshaft, and ANY machine shop that would do such a thing is NOT a reputable shop. You really do need to find a better crankshaft.
 
You could have them custom made as you probably know. Far as undersizes go, IH always ground their exchange shafts to .030 under on the gasoline engines although they offered the .010 and .020 bearings also. Some repair shops won't use any ground shafts, others use many different sizes. It is what you are comfortable with and have had experience with. And of course there are some shafts you just don't grind at all depending on material and hardening process they were mfg to.
 
HELLO-I WORK AT A MACHINE SHOP AND WE GRIND CRANKS,DO BLOCKS,HEADS,RODS,ETC.I WILL GLADLY CHECK MY SOURCES.I'LL GET BACK SOON.

TOMATO FRANK
 
You must log in or register to reply here.

Similar threads

W
560 Valve setting
2
Replies
23
Views
933
WHFarms
W
8
560 run a backhoe?
Replies
11
Views
533
caterpillar guy
C
S
Case g148b rod bearings
Replies
2
Views
250
Steve Hartwig
S
W
The “new” 560
Replies
9
Views
881
Ellis Kinney
Ellis Kinney
T
W9 fuel pump push rod dimensions
Replies
8
Views
284
John Deere D
John Deere D
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top