(800) 853-2651
SHOP NOW

660/Elwood action pics

Our Phone System is Down!

Please use the Contact us Form

We are working to resolve the issue ASAP! Thanks for your patience!

W

Wardner

Well-known Member
<a href="http://s140.photobucket.com/albums/r16/Wardner/?action=view&amp;current=660Elwood020.jpg" target="_blank">
660Elwood020.jpg" border="0" alt="Photobucket
</a>

<a href="http://s140.photobucket.com/albums/r16/Wardner/?action=view&amp;current=660Elwood015.jpg" target="_blank">
660Elwood015.jpg" border="0" alt="Photobucket
</a>

Yep, getting high on leaves.
 
Steel Wheel Ranch sent me a pair of fenders several years ago. I have the floorboard too. Just missing a few misc cowling or dust shields.

I can't run the floor board with the Fast Hitch. I can install the fenders with homemade brackets. Just haven't got around to it yet.

I bought the tractor with a cab. It was made well as the tractor was used as a orchard spray rig. It even had a big charcoal filter on the roof. I prefer open station.

Here's a pic of the front end. It's staying with the tractor.

<a href="http://s140.photobucket.com/albums/r16/Wardner/?action=view&amp;current=660Elwood001.jpg" target="_blank">
660Elwood001.jpg" border="0" alt="Photobucket
</a>
 
It's surprising how much resistance a few yards of wet, steaming leaves can exert when going up a 45° incline. Didn't want to go too high on that unstable footing. I probably wouldn't be found until the landscaper dude came back with another load.

He mows my lawn and I take care of his waste. I usually get enough wood to heat my barn as well. He also rakes my leaves. That's about eight big sugar maples.
 
Not trying to stir thinks up but- doesn"t the blade mounts cause interferance with the movement for the front axle? looks like there is not much clearance.
 
There's been no contact with the square tube and the axle housing as evidenced by the unmarked paint on both pieces.

The clearance in the picture is slightly distorted by the hydraulic jack. Deflection is about an inch. I would have set the jack closer to the front but it was too tall.

Anyway, if it did make contact, I wouldn't consider it a problem. There needs to be a limit for the oscillation and the factory provision isn't adequate.
 
You must log in or register to reply here.

Similar threads

D
Cutaway pictures
Replies
6
Views
612
Hobo,NC
Hobo,NC
T
Case Taylor Dyno Worth
Replies
3
Views
540
Trkr
T
H
Moline Plow Receipt
Replies
2
Views
1K
moll
M
H
JI Case Tool Kit
Replies
3
Views
670
Ande
Ande
H
Case toolkit
Replies
4
Views
855
Howard H.
H
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top