(800) 853-2651
SHOP NOW

1968 656 D International Farmall

M

Mike Karban

New User
I had to have my starter rebuilt for my above tractor and having an issue with the drive hitting the flywheel gear and not engaging the flywheel. The drive is a 12 teeth drive and I think i need a 13 or 14 teeth drive. The starter # is a Delco 1113198. I have been told it is a delco 30 mt starter. Does anybody have any ideas? Please send a private message or post on this site. Thanks Mike
 
The 656 used two different ring gears on flywheel and pinion gears on starter so you need to match serial numbers or start counting teeth. About 25 years ago one of the mechanics in shop installed wrong drive, it worked but made a lot of noise and I went out and installed correct one at the customers farm.
 
The manual stated that the teeth on the flywhell had 134 teeth and how can I match the pinion gear to that number of teeth.
 
Are you sure that the drive OD is not too large to engage the ring gear teeth? You can't rely on tooth count to get the right size OD on the drive gear.

The parts book lists two different drives for diesel starters but one is for the Hydro and the other is for the gear drive. The one for the hydro is a ten tooth with a 32 mm OD on the gear. I did not find any specs for the gear drive transmission drive but I did come up with another ten tooth with a 40 mm OD and a twelve tooth drive with a 46.5 mm OD. The 46.5 mm is the drive that is used on the 30 MT starters used in the 706.

The numbers I came up with for your drive are:
Delco Remy - 1965788
Acurite -3-276
Arrowhead - SDR5116
 
Thank you for that information. I spoke with a tech specialist at delco and he stated that the proper drive would be a 12 teeth with a 10-12 degree pitch. We are going to try that. I will stay in touch for follow up. Thanks again.
 
You must log in or register to reply here.

Similar threads

M
656 Farmall vs International
Replies
12
Views
723
BarnyardEngineering
BarnyardEngineering
4
International 424 tractor starter drive
Replies
6
Views
218
424Unicorn
4
K
international 656 hydro deceleration valve question
Replies
1
Views
192
tstoub77
T
W
1968 international 500
Replies
1
Views
272
Fritz Maurer
F
M
656 PTO slow to engage
Replies
14
Views
558
M Nut
M
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top