(800) 853-2651
SHOP NOW

New Owner of a Farmall MD...Parts???

M

Matt Weltz

Member
Just went and picked up my 1951 Farmall MD today. Starts easily on gas a switches over to diesel perfectly. Pump pegs out the pressure gauge even at idle. Oil Pressure is also very high. Rear tires are new and fronts are very good. Cost me $1300 and a 10-hour round trip. Anyway, anybody know where I can find a new exhaust manifold for it??? Thanks!
 
I don't know of anybody who makes a reproduction, but I haven't been looking either. It shouldn't be too tough to find one at a junk yard.
Why do you need a new one? Are you sure you can't weld it back up? My local welder is a wizard at welding cast and has saved me a lot of money in just my SMTA exhaust manifold.
 
No new ones around unless you can find a NOS one. I have one that I would sell to you if you need one. It is good. Let me know.
 
(quoted from post at 06:29:57 09/12/10) Mine has a hole rusted out in the bottom and the top pip is broken off. Not sure if it could be fixed...
Click to expand...

The top pipe is no big deal. That is why I needed mine welded up. If the hole acutally rusted out on the bottom there probably isn't much to weld to so it couldn't be fixed easily. You could probably weld a patch over it and be good to go if it is in a flat place. It sits up under the hood enough that you and the people you told would be the only ones that knew it had been repaired. It is your money so do what you see fit.
 
I think the dumest thing I have done is I purchased a Dozer 9 WD 2 ser#98457 International I am told it is like TD9 need manual any help would be appreciated. Thanks John
 
I have one the piece that bolts on the top is gone that your muffler would slide over and the two bolts are broke off but there is enough sticking out to get a hold of. could heat them up and turn them out. other than that it is in good shape. Make you a great deal.
 
You must log in or register to reply here.

Similar threads

F
Deere 4020 New Owner Questions
2
Replies
29
Views
1K
FFFAM
F
V
new owner of a 620, will try to update this as we go.
2 3 4
Replies
61
Views
3K
valiant8086
V
J
Low oil pressure on a JD950
Replies
2
Views
2K
bmaverick
bmaverick
M
New-to-me JD-A and JD-B Repair Tips
Replies
13
Views
938
Fixingfarmer
Fixingfarmer
Z
Farmall c knocking?
Replies
16
Views
986
Zsprankle
Z
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top