(800) 853-2651
SHOP NOW

C-21-P Mower hookup to Super C

B

Brent P

New User
Is there a picture or diagram on how to hook up a C-21-P mower to the Super C. I need to figure out what to do with the stabilizer bar (?) on the right side. I'm new to the fast hitch system.
 
Are you looking at the draft rod that attaches to the Touch Control on the right side? You can disconnect it from the Touch Control and pin it to the housing on the right side of the torque tube. You don't need it for a fast hitch mower and you do need the touch control (as I recall) on the left side to raise and lower the cutter bar. To stop lateral swing, you need to relocate the pins in the lateral links to pin it solid. Mowed a lot of hay with one years ago, but it has been 50 years ('56 thru '60) so my memory may not be exact.
 
We had one of them mowers when I was a kid and I thought I remembered a bar hooked to a clamp on the right axle. Then I remembered I have a fast hitch attachment book that took a while to find. The part you're talking about is a auto release coupling bar, a couple of flat bars with a hook and a spring. It hooks to a rear axle attachment clamp, looks like the drawbar clamps on an M only it fits the Super C axle.
That auto release bar breaks away if you hit some thing.
 
It appears that there is suppose to be a big eye bolt on the bottom of rear axel clamp that this bar attaches to. I guess I will need to find out how to put on a new one.
 
(quoted from post at 20:40:05 08/27/10) It appears that there is suppose to be a big eye bolt on the bottom of rear axel clamp that this bar attaches to. I guess I will need to find out how to put on a new one.
Click to expand...
Ours did not have anything like that, just the lateral swing stops built into the Fast Hitch. As I recall, the mower had a built in "breakaway" if you snagged something. Before that we had a C with a #5 JD mower and it mounted to the axle clamps like the rear of the cultivator on the C. I don't remember what the model number on the IH mower was, but it was Fast Hitch and no wheel on the back like the JD.
 
You must log in or register to reply here.

Similar threads

F
International C-3 Mower on a C
Replies
6
Views
307
toothpick
T
H
Farmall Super C
Replies
2
Views
392
rustred
rustred
D
Rear mount sickle mower for Super C w/ mid mount belly mower
Replies
6
Views
485
gene bender
G
J
1953 Farmall Super C with a 2-wire distributor.
Replies
5
Views
193
Joe Kimbriel
J
R
Super C disc brakes
Replies
11
Views
387
Levi81
L
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top