(800) 853-2651
SHOP NOW

Farmall 400 axel bracket for draw bar

S

Spotted Horse

Member
While moving big round bales yesterday, I heard a "loud pop" and noticed the bolt that goes under the axel housing broke off. I don't know what this bracket is called, or what the part # is, but I figured someone here might know.

I need the rear part of the axel housing bracket, plus the two 7/8" X 8" bolts that go over and under the axel housing.
If anyone here on this forum has these parts for sale, please give me a shout.

Here are a couple of pictures of the bracket that fits between the axel housing and the Saginaw 3 pt..

Looking down at the bracket.
TractorBracket002.jpg


Looking at the bracket from the front. (front part is OK, I just need the rear part))
TractorBracket001.jpg
[/img]

Thanks,
Spotted Horse
 
Should be easy to find in salvage yard. My early 30 year old Saginaw has 2 brackets on each side and has carried some heavy loads (like 4 row planter) and is still in good condition.
 
I have an old Saginaw 3 pt. on my M, and it has 2 bolts through the bottom (I'll bet your's does to), but this new Saginaw (I just bought it 3 days ago) and the Farmall 400 brackets, only have 1 bolt through the bottom.
 
If anyone has the square tube that fits the rear of the axle housing, complete with two 7/8" X 8" bolts, for sale,... please let me know.

The hole in the bottom of my rear tube (for the long bolt) is completely torn out and ruined.

I think the tubes are all pretty much the same on the Farmall M thru Farmall 400/450.

Thanks,
Spotted Horse
 
IH didn't make the square tube. They bought it just as they did with the frame channels along side the engine.

You can also buy that tube at any steel supplier. I would replace it with solid square bar as your application probably exceeds the IH engineers calcs.

Got a drill press? Got a bolt supplier who can furnish grade 8 bolts? Fastenall should be nearby.

That repair would have only caused me about one hour's downtime. My junk pile is a handy resource.
 
Have a saginaw hitch on my super m. Was bending brackets very often. Took a piece of solid steel and inserted in the tube. Didn"t bend another one. Dick in Vermont.
 
You must log in or register to reply here.

Similar threads

J
Looking for a WC draw bar extension
Replies
18
Views
704
wolfman
W
D
Farmall Super H battery box light bracket
Replies
4
Views
340
caterpillar guy
C
taburge
Looking for a 284 Diesel Thermostat Housing
Replies
2
Views
124
BarnyardEngineering
BarnyardEngineering
K
8n ignition switch bracket?
Replies
2
Views
201
Eman85
E
N
IH 544 Hydro Wheel Spacing or other suggestions
Replies
4
Views
544
newtron
N
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top