(800) 853-2651
SHOP NOW

200 single front wheel bushings

C

couv

Member
Broke it down, right side of axle & bronze bushing seemed good, left side of axle is a bit worn which caused wear in the bushing.

Ideal fix would be replace 2 bushings, 2 seals, and have axle built-up and machined down to spec. Anyone have an idea of costs ?

I need
(2) lock washers #23743D (bend-tab to keep axle nut from backing off)
(2) #364469R91 seal ( C.R.#12124)
(2) #361311R1 bushing

who is my best source ?
 
You should be able to reuse the lock washers. Since you have the CR number, about any place that sells seals. CaseIH will be the highest, but if sent with their stock order (3 days here), you will not get charged for shipping. Shipping from any other place if not in stock will likely cancel out their price advantage. The bushings, will probably come from CaseIH if they still have them, otherwise you will have to have them made, unless you can get exact measurements and can order them. If you have to have the axle machined, let the machinist make/purchase the bushings -- I would not do much to the axle unless it is noticably worn. Machinist cost, including bushings, less than $100. Seals maybe $15 each, depending on size, don't remember what those particular seals look like.
 
The washers are still available from CNH for $8.80 each. The seal is discontinued by CR and CNH. You will have to take it to a parts store for measurement to attempt to find one that is close. The bushing has also been discontinued by CNH. You will have to have a machine shop make them for you.
 
I have one of those singles on a 'C' that is on my list of things to do. The bushing and washer did not cross but the seal did, and as has been said with a CR# you should be able to get it at any good parts house.

Part Number NOS 12427
Seal, 1.25"; 1.987"; .25"
Product Line: NAPA Oil Seals
Interchange Mfg.: Navistar (IHC)
Interchange Mfg. Part Number: 364469R91

10.99 Each
NAPA search page
 
You must log in or register to reply here.

Similar threads

stevieb49829
Progress on the 101 Jr front rebuild-this is LONG
Replies
5
Views
562
Stan Coryell
S
B
S7 200 amp Inverter Welder review $99
Replies
17
Views
3K
bc
B
C
2630 John Deere throttle govenor hand and foot linkage
Replies
8
Views
2K
chickenfriend
C
E
Farmall H Bolster/Steering Rebuild
Replies
12
Views
7K
Silverstar
S
A
YM336D YM3110D Front Axle Seal Replacement
Replies
0
Views
72K
markey-HT
M
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top