(800) 853-2651
SHOP NOW

rear light bracket, Farmall H w/pic

F

FarrviewWest

Member
This light bracket was on my "41 H when I bought it. I have searched the archives and google and have not found a picture of how it is PROPERLY attached to the tractor (when I took it off, I assumed it was not attached properly since the pto lever was not connected to it).

Can someone post a picture of a properly attached light bracket?

Also, to the correct police: is this bracket correct for a 1941 H?

Thanks to all in advance!
a12064.jpg
 
Its from a early H or M mostly on ones with sloted transmission tops. Lighting was considered a attachment on those tractors so its hard to put a date the parts were used. can't say it wasn't on a 41 from new. Can't remember for sure the mounting, think one trans cover mounting bolt and a 3/8 hole in trans cover.
 
You got me curious so done some checking. That bracket 9231D is the only one shown in parts books through 1942 and at least part of 43. They went to 9231DA later and then a 6 digit #. Mounting hardware called for is a 7/16 X 3-1/4 NC hex head cap screw. 3/8 X 1-1/4 hex head cap screw lock washer and nut. 7/16 bolt would be a little longer one for the transmission cover.
 
thanks for that info D Slater, it helps solve one of my problems. I"m still holding out that someone has a pic of proper attachment. I"m not sure my t-deck (later type, not slotted) will accept proper attachment, which is why I am so curious.
 
The hole that is to the left of the number 9 is used for the rod for the pto to go through. it is up side down right now. It bolts into the one cover bolt then goes around the left corner of the cover and ends up under the cover on the one the side. This is what is used on my 39 M and H
 
O.K., with the information from you guys I was able to figure this out. The transmission cover I have on my 1941 H will not accept this light bracket because there is not a hole for the 3/8" bolt to go through. I happen to have a transmission deck from a 1944 H and it has the hole for the 3/8" bolt. I lined up the bracket and it seems to be just right.

Mystery solved! Thanks for the replies, I've been racking my brain over this for awhile!
 
You must log in or register to reply here.

Similar threads

D
Farmall Super H battery box light bracket
Replies
4
Views
360
caterpillar guy
C
D
Farmall B - plow (bracket?)
Replies
9
Views
511
DoubleJFarmsWA
D
D
Not sure what I have on this H
Replies
3
Views
562
matthies
M
R
Need help with Farmall M 12V wiring
Replies
17
Views
529
used red MN
U
K
Broken Fast Hitch Bracket-Farmall 450
Replies
5
Views
322
used red MN
U
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top