(800) 853-2651
SHOP NOW

Super C Hydraulics

L

lbm

Member
I am wanting to add a hydraulic remote to run cylinder lift implements, with my super c. I have looked around locally to find one with this set up but unable to find one. Any help and guidence would be greatly appreciated.
 
You need the block that will go on the rockshaft housing and the tubes coming from the pump will bolt to it. Then you can run lines out to the control valve you are adding. Depending on what cycl you plan on using you will need to add more storage for hy fluid. I have a block i would sell. send e-mail if interested.
 
If you don't have Fast-Hitch, find a SC, 200 or maybe a 230 with F-H in a salvage and get the parts for the F-H control. If you already have F-H, you can cap off the F-H cylinder and plumb into those lines. I think IH even made a solid rod to replace the cylinder if you can find or make one.
 
The tractor does have a fast hitch. I won't be able to use the hitch if I use it this way, right ?
 
(quoted from post at 17:00:39 01/03/10) The tractor does have a fast hitch. I won't be able to use the hitch if I use it this way, right ?
Click to expand...
That's right, you won't be able to use them both at the same time. I'm sure there is a way to tap into the system and operate both at the same time, but I'm not familiar with how this circuit works. I do know you could put a flow divider off the pressure line of the pump (I have seen these at TSC) and then add an open center 4-way valve. However, this will always rob flow from the existing system and slow everything down... you probably don't want that. If there is a way to add it to the existing system without the flow divider, that would be better. What you would need is a valve to parallel the Fast-Hitch valve.
 
I have a 200 with a FH and another valve I use for loader or one way cyl. I had to install a blk between the FH valve and the Touch control. I have seen the blks on this sight before.
 
You must log in or register to reply here.

Similar threads

J
1953 Farmall Super C with a 2-wire distributor.
Replies
5
Views
193
Joe Kimbriel
J
D
super c , loader
Replies
7
Views
324
kub6040
K
R
Super C disc brakes
Replies
11
Views
387
Levi81
L
C
Wiring lights on a Super C
Replies
6
Views
280
560Dennis
560Dennis
M
Super C Carb Identification
Replies
4
Views
274
mainer76
M
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top