(800) 853-2651
SHOP NOW

IH 8-16 Restoration Help Needed!!!

A

Anonymous-0

Well-known Member
I'm in the process of restoring an 8-16 that we have had for many years. I'm looking for a source for repro sheet metal (hoods, fenders) as well as engine parts (piston rings, gaskets etc.) Can anyone help?? There was a fellow in Canada making sheet metal several years ago. Anyone know him??
 
If you go to "Smokstak" and ask that question you will find a feller from california that would probably still have some parts. I believe last name is Farbor. Good Luck!
 
Welcome to the 8-16 restoration club... I am currently doing a 1917/18 VB series, and a 1922 IC series. Interesting tractors.. What series is yours? VB, HC, IC?? Engine parts will vary by series.
 
I supplied hood measurements from my grandfather's 1922 8-16 to the fellow restoring the one on "You Tube .. International 8-16". Contact me and I'll sent you his e-mail address.
Walt
 
Mine is also a 1917 VB. Very early with the Maddison Kipp oiler on the side of the engine. How far along is your 8-16? Any leads on repro sheet metal??
 
I got reproduction fenders for my 10-20 from Tired Iron Farm in Bristol Ind.
This has been some time ago, but worth a try. Their phone number is 219-848-4628.
Good luck on your project. :D
 
Any good metal shop can make you a hood & fenders if you have the old parts so they can get the dimensions. There's a man not far from me that makes fenders for the Mc Cormick Deering tractors. You can contact him at 717-548-4131.
His name is Robert Lefever in Peach Bottom, PA.

Contact Dean at [email protected] as he make hoods. Hal
 
Kinda working on just finding the parts I need. Mine is awful rough. I am needing to possibly find some patterns to cast for mine, but shoot me an email, we may be able to help each other out.
 
You must log in or register to reply here.

Similar threads

G
8 john deere LP 4020 tractors and 3, 3300 combines being converted to propane.
Replies
19
Views
945
Tx Jim
Tx Jim
M
Farmall 140 Cylinder gets tight after one minute of running.
Replies
17
Views
601
560Dennis
560Dennis
J
1940 Case V battery box/hood latch?
Replies
4
Views
401
JHH
J
H
IH574 Gas Tractor with a 3/8" Bolt in the Carburetor Outlet
Replies
9
Views
398
stevieb49829
stevieb49829
W
New to forum - SOS interest
Replies
8
Views
744
Greg NE
Greg NE
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top