(800) 853-2651
SHOP NOW

IH 240 Utility hydraulic hose adapters.

G

GA Dave

Well-known Member
I had a hydraulic hose to blow today. No problem, I had bought a couple spares several years ago. I thought they would fit BUT! The new hose has 1/2" I assume NPT fittings (one swivel) on both ends. New hose is a tad too big to fit the hydraulic cylinder and a tad too small to fit the ? under the seat. Seems I need two different size adapters to use the 1/2" hoses. Anyone ran into this problem before? Have a part number on the adapters? Many thanks. David...................

hydhose.jpg
 
I would take the blown hose to a shop that makes hydraulic hoses and have a new hose made with correct end fittings. Looks like the other hoses have a female swivel nut that connect to JIC male tube fittings. Hal
 
the fast hitch hydraulic hoses are an o-ring type fitting, not npt threads. i had a hydraulic hose shop make me up 2 new hoses for my 240u.
 
I had a similar problem with my 240U until I deciphered the hydraulic hose fitting system, which was initially about as clear as mud.

Here"s some basic information.

This is a useful site, with helpful diagrams. They also have adapters that may help save the hoses you had made.
Hose fittings
 
I took the two hoses to the local hydraulic shop and they fixed me up with adapters. The two 2' hoses I had were less than $10.00 each so I think I got by with less than if I had them to make me two new ones. I only changed the busted one out and will do the other later.Only took 1/2 gallon of fluid to refill. It sure looked like a lot more had sprayed out. Notice the old hose didn't have o rings but they didn't leak. David..........

Hydraulicadapters.jpg
 
If you you have a Colliflower Inc store in your area they can make any hydraulic hose with the correct fittings. They should have a store in Atlanta. They have a lot in stores in VA, PA and here in MD. I was in the store on this side of Baltimore to get a 5/16 push on swivel nut. They had a man in there just making new hydraulic hoses. Hal
 
You must log in or register to reply here.

Similar threads

Z
Farmall 656 transmission suction hose---is it a special size?
Replies
3
Views
224
zooeyhall
Z
G
Need hose that goes from hydraulic tank to hydraulic motor on 1980 Ford 445 diesel
Replies
2
Views
181
gnc23
G
Btzj02
Ford 960 Power Steering Hydraulic Hose Replacement
Replies
2
Views
218
Sean in PA
S
F
The cost of hydraulic hoses
Replies
8
Views
838
caterpillar guy
C
R
Ford 860 - Need to Replace Front Hydraulic Pump Suction Hose for Loader
Replies
2
Views
110
Jim.ME
J
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top