(800) 853-2651
SHOP NOW

Fast Hitch Farmall C

A

Anonymous-0

Well-known Member
Is there a way to adjust the two receivers on a fast hitch to gain a fraction of an inch additional distance between them. I have an impliment that is 1/4 of an inch to wide and I haven't found a way to create even that much play between the receivers.
 
All the small-point implements should be the same width to fit in the C Fast Hitch. There is no way, short of heating and bending, to spread those receivers further apart then they are now.

I'll ask, though....are you sure the implement you want to insert, thats too wide, is made for your C? Implements made for anything 300-sized or larger, have bigger (wider, taller) points and that added size would make the spacing wider. Even if spaced the same, those large points would not fit into the fast hitch on your C.

AR
 
(quoted from post at 11:17:13 09/14/09) Is there a way to adjust the two receivers on a fast hitch to gain a fraction of an inch additional distance between them. I have an impliment that is 1/4 of an inch to wide and I haven't found a way to create even that much play between the receivers.
Click to expand...

Carl, There is no adjustment on spacing to the sockets on the fast hitch. Both large and small prong fast hitches use the same 28" spacing.Small point FH implements will fit into large socket FH with the use of 1/2" thick filler plates. The only difference between the large and small FH is the 1/2" height difference of the points(3"' high on large vs. 2 1/2" high on small).
My guess is either the bail( the part of your fast hitch with the sockets on it) or the prongs on your implement are bent or sprung.Measure both hitch and implement to see if they are 28" center to center.If either one is sprung or bent, the use of a hydraulic porta power or other method of straightening is called for.Hope this helps,Mark
 
You must log in or register to reply here.

Similar threads

B
Farmall Fast Hitch Plowing
Replies
10
Views
1K
Absent Minded Farmer
Absent Minded Farmer
F
Farmall 130 hitch conversion
Replies
16
Views
647
BunkumBen
B
A
Field Cultivativator for Farmall 140 fast hitch.
Replies
3
Views
502
peteL
P
K
Which fast hitch?
Replies
5
Views
527
Jim Becker
J
D
Super C Sickle Mower axel clamp or cylinder stop?
Replies
5
Views
423
Don Mountain
D
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top