(800) 853-2651
SHOP NOW

560 farmall teledepth valve

C

casered

Member
Hi guys on my 560 I took the valve stack off to put in new seals and when I reassembled it I didnt have the gears in the tel-a-depth valve timed right, (even after using an IT manual). I know this because the fast hitch came all the way up and would not go back down. Now I have broken gears inside the valve and need to replace them.

My questions are:
1) Who is the best place to look for this series of tractors for parts? I have tried a couple local guys with no luck.
2) After I find said gears is there a better way than by how the IT manual tells you to time it to get it right? I thought I did it right the first time but didn't.
3) Is it because these things hard to find that I am having no luck getting ahold of them. I have been even watching Ebay with no luck.

Any help would be appreciated as I would like to get this back together soon so I can start using it again.
 
No good ideas where you can locate the gears except salvage yards, but will add, you may have timed the gears correctly and got the lever (eiether side) on wrong and that will do what you described. On reassembly, I would not hook the linkage to the lever , and operate it by hand to see how hitch reacts in relation to positon of lever. Other choice, replace the teledepth valve with a regular valve, throw away all the linkages to the hitch and just raise and lower hitch as you would any other cyl, like previous models did.
 
A quick check to see if the gears are timmed correctly so that you don't ruin another set of gears is to look at the position of the center gear before you start the tractor. If the hydraulic spool is centered in the neutral position that center gear will be straight down and form a right angle to the spool. That is assuming the control lever is in the raise position when the hitch is all the way up or the control lever is in the down position when the hitch is all the way down. Do not start the tractor with the linkage disconnected.
Chuck
 
You must log in or register to reply here.

Similar threads

W
560 Hydraulics explained
Replies
13
Views
607
BarnyardEngineering
BarnyardEngineering
W
560 Valve setting
2
Replies
23
Views
928
WHFarms
W
L
Farmall 560 Diesel Alternator Conversion
Replies
5
Views
229
used red MN
U
G
Farmall 560 Hydraulic issue
Replies
2
Views
315
Janicholson
Janicholson
B
My 2400B (464) 3 pt will not go down
Replies
0
Views
27
baker355
B
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top