(800) 853-2651
SHOP NOW

Seals for M transmission input shaft and counter

T

Trapman

Member
Howdy, I'm having a hard time locating the right seals for the M that I'm working on and my problem is the nearest IH dealer is 3 hours away so I have been searching the various web sites for these seals and can't seem to "turn over the right stone" so to speak. The seals I'm looking for are the Transmission input shaft seal and also the countershaft seal. I've found the countershaft seal at one place but did not order because I'd like to get them both from the same place. We do have a Napa in town has anybody gotten any of these seals thru them? If anybody knows of a website where I can locate any of these parts???? Thanks in advance.....
 
Should not be a problem -- NAPA can cross the numbers for you as can any good seal/bearing place. They may have to order them which should only take a day.
 
Online you can try ebatmus.com
Type in the dimensions in the search box, OD X ID X Width and you should get something.

I bought some bearings from them. Prices were good.
The Napa thing should work too.

If nothing else you might get some good part numbers to give to the Napa guy to look up.
 
I second the recommendation for Napa to cross-over a CIH number.

I just did it this morning on my Super A for example and they also have the Speedi Sleeve I need in stock as well.
 
I also need these seals and also seal for LiftAll pump. The Bates Corp. either has or can get all these seals for you. Website is www.batescorp.com
 
I was only able to get the one ordered through NAPA and that was the top input seal the other one they could not get and I had a National number and also an original IH number for them as well. Looks like I'll try the Bates website.
Thanks guys......
 
It sometimes pays not to clean your bench. I just went through this with a early 53 Super M. The top seal from napa is #20702 but they could,nt find the lower one. The lower one from IH is 381907R91 and you need two of them. If ya happen to need that little steering shaft seal it's a napa 9876, now I can clean the bench.
 
You must log in or register to reply here.

Similar threads

C
Super C input shaft seal replacement
Replies
1
Views
131
Charlie M
C
M
821 w/4 speed input shaft load bearing snap ring?
Replies
4
Views
165
pomester
P
B
Wheel Horse Charger 12
Replies
5
Views
775
timcasbolt
timcasbolt
D
new load shaft seals are leaking
Replies
7
Views
634
Dan in North Houston
D
P
YM 1810 clutch output shaft
Replies
0
Views
2K
winston-HT
W
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top