(800) 853-2651
SHOP NOW

Aftermarket dual hubs,1566.

Our Phone System is Down!

Please use the Contact us Form

We are working to resolve the issue ASAP! Thanks for your patience!

S

Sean in P.C. NE

New User
Are there dual hubs that a guy could run 10 bolt 18"x42" rims say from a Case IH magnum tractor? I converted the inner duals from 20.3x38 to 18.4x42 tires. The tire place had the step rim of 18x42" for the cast center of 38", but I don't want to run my current M&W 9 bolt hubs that are 1/2" fine thread studs. The guy before me was breaking these studs fairly easy. The 10 bolt has the bigger bolts(3/4" bolts I think). And I think those would hold up much better. Does anyone know of such a hub for the 3-1/2" axle of the 66' series tractor? I know the Magnum tractor is different but axle size i think is the same 3-1/2". Any help would be awesome! Thanks!
 
Im not sure what you are doing but i think you want to put the hubs from a magnum on a 66 series tractor. You might be able to just change the wedges and keep the hubs. underferth has what you need i think. I did that ,went from a magnum to a puma and they had the wedges for the hubs.
 
Yeah could give that a try. The only difference between the 66' axle and magnum is that the 66' has the "rib" and I believe the magnum has to notches 180 degress apart. Just like a dual keyed shaft. Yeah remember now that the magnum uses two wedges with ribs on each one to fit the axle. If Underferth would have such a conversion of one half wedge being a half circle, and the other half to fit the 66' series top cut outs that would be perfect! Thanks for the help Erik!
 
You must log in or register to reply here.

Similar threads

J
Dual Hub Bolt Pattern
Replies
0
Views
209
jsferden
J
R
1030 rear axle
Replies
3
Views
548
used red MN
U
R
Super C bull pinion gear retaining washers/bolts
Replies
12
Views
362
300guy
3
R
Super C Bull Pinion Gear Retaining Washer & Bolts
Replies
3
Views
210
RTNystrom
R
D
Oh,,,, That's why it's leaking. Too big a job for hobbyist?
2
Replies
30
Views
2K
docmirror
D
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top