(800) 853-2651
SHOP NOW

Farmall NF Pedestals: 300 VS. 400

M

Matt Weltz

Member
Hello! I was wondering if the 300 and 400 use the same NF pedestal? I know the bolt pattern is the same but did not know if the 400 had a taller pedestal or not. I have a wide front on my 300 with mounting brackets for a 400. I cut them down to fit the 300 but the front end of my 300 is way up in the air. i just bought a 400 so would like to put the wide front on it and go back to a narrow front on the 300. Will have to re-extend the wide front brackets I know.
 
The NF pedistal flange does not have the same bolt pattern as the M. Some redrill, but it isn't a best solution. (I think they are the same height. JimN
 
I am pretty sure all the pedestals have the same bolt pattern from the H all th way up to the 560"s. Maybe slightly different but will all match up to each other with some slight boring. My only concern is whether or not the 400 pedestal is 2" taller than the 300"s pedestal as the wide front mounting brackets are.
 
Bolt patterns are different. H, SH, 300, 350 & 460 same. M, SM, 400, 450, & 560 same. Height should be about the same.

Harold H
 
We build IH pulling tractors, & we change front ends around alot. I got to TELL you, 300 & 400 front ends WILL NOT interchange; not even very close...
 
Just a slight difference in height. If you are refering to the dual wheel narrow front lower bolster, Jim answered it first. Bolt pattern is different on H to 350 compared to 400. also they used 5/8 diametter bolts for mounting and others used 3/4 inch. If you drill a 300 one to fit a 400 the bolt holes will be razor thin on edge of bolster or broke out the edge. 460 used the same 4 bolt mounting pattern at top end as a 560.
 
Don't know about the height of either, but what size wheel rims do they use? Could you put on smaller rims to lower the tractor front?
Just thinking -maybe wrong.
 
You must log in or register to reply here.

Similar threads

B
single front wheel Farmall questions
Replies
7
Views
410
DeltaRed
D
M
Case 400 Diesel
Replies
5
Views
382
cumminstinkerer
C
C
Farmall 400 With 0-264 Engine Radiator Part Number Location.
Replies
5
Views
216
cal556
C
S
My new to me 300 U
Replies
3
Views
294
Janicholson
Janicholson
1
Int 300/350u front hyd pump
Replies
3
Views
197
13fx
1
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top