(800) 853-2651
SHOP NOW

Hydraulic Drive shaft cover plate?

D

David Goode

Member
Correct me if im wrong, but I thought there was someplace that sells a cover plate to go on the drive shaft to the old Hydraulic pump if Your tractor has been converted to live hyrdaulics. Is it just my imagination or is there really such a thing for a Super M? Thanks
-David Goode
 
The one for a Stage 2 SM should work. There may be a flat one also. The Stage 2 one has the same holes in the bottom for attaching implements/cylinders as the Stage 1 with the lift all. Call Mike at Steel Wheel Ranch 785-548-7437.
 
they kinda look like this?? this was from a kit that was an add on live pump for an m. the old belly pump housing would be converted to a resevoir by bolting this cover in place of the pump , increased the volume the pump housing would hold.
<a href="http://s121.photobucket.com/albums/o234/glennster_01/?action=view&current=DSCF1516.jpg" target="_blank">
DSCF1516.jpg" border="0" alt="Photobucket
</a>
Untitled URL Link
 
(quoted from post at 15:59:21 12/13/08) they kinda look like this?? this was from a kit that was an add on live pump for an m. the old belly pump housing would be converted to a resevoir by bolting this cover in place of the pump , increased the volume the pump housing would hold.
Click to expand...

Do they still make those?

That what I need for my Super M. You wouldn't happen to know how much more capacity it adde?

K
 
Then is there anything you would put over the old shaft that goes into the transmission? Like a cap or something? Just something so you don't have anything spinning anymore. Thanks for the pict.
-David
 

With the belly pump reservoir in place, and the access panel in place, you can't put your hand up in there, and it's covered.
 
Yes a cap goes in place of the housing held by 3 bolts that counter shaft seal goes in. Hydraulic unit drive lug gets removed from counter shaft and heavy washer and a nut goes on before the cap. Get the parts from all W6, SW6 tractors or SM that came with live hydraulic. No seal needed then, just a gasket for the cap.
 
You must log in or register to reply here.

Similar threads

W
Farmall Super M Hydraulic Shaft Seal
Replies
5
Views
668
Janicholson
Janicholson
J
IH Super C engine help
Replies
15
Views
679
jaburford
J
C
1960 case 540 torque tube sections fill one to fill all
Replies
9
Views
533
used red MN
U
R
JD 4630 hydraulic problems
Replies
14
Views
629
rolsen05
R
S
2020 hydraulic pump leak from drive seal
Replies
10
Views
426
WTW
W
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top