(800) 853-2651
SHOP NOW

340 t.a. HELP

M

Mark W.

Member
I have lost the high range in my 340 utility. I thought it was more common for the low range to go out. Am I looking at a rebuild or adjustment? It had been working great up to this point with no slipping.
 
If the TA clutch wears out, it will not allow direct drive. THe TA clutch "locks up the planetary gearset in the TA making it drive direct. When it slips, it allows the Gears to reduce the ratio, and the one way Ramp/Rollers clutch keeps the TA assembly from turning backwards. It is somewhat uncommon, but is easily repaired (with a split). I would replace the one way clutch and the TA clutch, and the master clutch/Throwout bearing while I was in there. JimN
 
You may have completley lost the ta pressure plate and disk and maybe even the t/a flywheel. I have t/a replacement parts if needed. Feel free to send me an email.
 
It was because I started typing a short congratulations to a successful repair, and for got to switch to the message box. The content got stuck into my browsers auto fill "mind" and appears when I open an Add a Reply to anyone. Oh well. If I am in a hurry, I forget to swap it out to my regular Janicholson, Good evening Andy, Jim
 
Jim, to make your PC remember you as Janicholson again, just click into the Farmall board, on the top of the page there is a link called "Login Status", click it and log out. Make a post again and you will need to sign in again, it should remember you as Janicholson.

Andy
 
Go to post a message, clear out the name and click once in the box, it should bring up names you have used, point to JanicholsoncantBeatthat and push the "Delete" button on your keyboard. Type in your name, Janicholson and make a post, I think this would fix it, but I'm not sure. If you still have problems, email Chris.

Andy
 
If your TA clutch disk still is the original style with riveted lining it is not unusual for the line to come off and the high side will no longer work. Letting the tractor free wheel down a hill in the TA position will over speed the disk enough for the lining to break off from the rivets.
 
You must log in or register to reply here.

Similar threads

B
Farmall 340 Engine
Replies
4
Views
365
gene bender
G
L
IH 340 power steering not driving evenly
Replies
18
Views
699
livinadream55
L
B
Another Farmall 340 Question
Replies
7
Views
271
fastfarmall
F
M
International 340 Utility PTO Issue
Replies
10
Views
414
militiaman11
M
E
2955 hydraulic issue
Replies
11
Views
1K
Eric in KY
E
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top