(800) 853-2651
SHOP NOW

touch control rebuild questions

T

too many interests

Member
HI there,
I am rebuilding the touch control on my super c and are having a few issues. I have an I&T service manual was looking at the exploded view of the touch control unit and it is showing o-rings/seals where I did not have seals when it came apart. Did the units vary a little bit or did those seals disentigrate and disappear in the past 58 years.
the numbers on the side of the unit were 354352 and below that 322w. Any help is greatly appreciated. I do not want to take it apart again as it is getting chilly out to work :)
Thanks
chris
 
Chris,

There are (at Least) two variations of the touch control block used on the Super Cs. The serial number split was at 191866, but someone may have replaced the hydraulic block in the past 50 years.

The parts book has the best pictures and there is a Serviceman's Handbook GSS-1024 (binderbooksdotcom) that covers rebuilding the touchcontrol. There was also a lot of discussion this spring as about 3 or 4 of us were rebuilding the blocks at the same time. Try searching the archives for those discussions.

Greg
 


thank you. I just wanted to make sure before I put it back together. I will have another scan of the archives to see if there was anything I missed
chris
 
(Hey Greg! How ya doing?)

TMI, a couple of pics from my SA, which had a Pesco pump, if yours is similar to mine. The arrow is pointing to the part of the body that contains the O-ring or seal (some had one, some had the other) that keeps the hydraulic fluid from escaping forward into the engine.

pump1.JPG


In the second pic, the shaft with the arrow goes through the front part of the body, and the important 0-ring-or-seal sits around this shaft. and is within the bore in the body.

pump2.JPG


I had to scrape paint to find the numbers on the pump, but IH has a rebuild-kit (you can see part of it to the left) and they are specific to certain pumps.
Let me know if you have other questions.
 
You must log in or register to reply here.

Similar threads

W
584 Hydraulic control assembly
Replies
3
Views
132
wwoodrow
W
S
hydraulic fluid for Touch Control
Replies
15
Views
690
560Dennis
560Dennis
Country-Boy
Kohler engine rebuild progress and questions
2 3
Replies
42
Views
2K
Mike(NEOhio)
M
L
control unit for a Strongway gantry crane trolley
Replies
14
Views
638
ltknutson
L
O
D-14 Power Steering Seals and Secrets
Replies
3
Views
546
DrAllis
D
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top