(800) 853-2651
SHOP NOW

Crank Pulley f/ C-146 Engine

R

Rambarn

New User
I need a crank pulley for a IH-660 High Clearance Sprayer. It has a C-146 gas engine Ser#15908. It measures about 6 1/2" OD & has a bolt that goes thru it to pull it up on crank. This machine is mid to late 1960s model. If someone has this part or could tell me where to look for it, it would be very much appreciated.
I have tried a couple of Case-IH dealers & they can't even find the 660 High clear in their books.

Thanks Jim B
West Texas
 
Call these numbers to see if they have a used pulley. Hal
785-548-7437 or 608-455-2411
PS; What's wrong with old pulley?
 
Thanks TORO I'll give them a try. My old pulley has the outer cast iron edge broke all the way around. We were putting on herbicide in a pecan orchard & hit a hole that the feral hogs had left, broke the front wheel completely off & nose dived into the ground. I have other broken parts too, but this is the only one I haven't been able to locate.

Thanks Again,
Jim B
West Texas
 
Not sure, but I would imagine that the regualr 660 would take the same pulley. Just leave out the high clear part and Id be almost willing to bet youd find it.
 
(quoted from post at 16:35:21 08/26/08) Not sure, but I would imagine that the regualr 660 would take the same pulley. Just leave out the high clear part and Id be almost willing to bet youd find it.
Click to expand...

TORO, The pecan crop is average-good, had a great crop last year.

John M, This is a IH-660 High Clearance sprayer, looks very much like the John Deere HiBoy. This machine has a C-146 4cylinder gas engine & the 660 IH Tractor is a 6 cyl, so doubt that it will work.
 

:D Thanks El Toro- The SteelWheel Ranch was able to fix me up. What a great bunch of folks & info on this site. This is my first dealing with the IH folks, but they came through just like the Ford folks that have helped me out in the past.

Thanks Again,
Jim B
 
You must log in or register to reply here.

Similar threads

4
420 C engine questions
Replies
5
Views
466
M-MAN
M-MAN
I
Farmall c with 404 engine issues
Replies
7
Views
394
wore out
wore out
Dennis P
C-135 engine
Replies
2
Views
2K
Jim Becker
J
S
IH 674 Gas (C-200) Engine Balancer
Replies
2
Views
523
Fritz Maurer
F
M
Farmall C questions
Replies
16
Views
4K
Mike Wheels
M
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top