(800) 853-2651
SHOP NOW

IH 460 w/ 291 motor

U

uncle fred

Member
I am in the process of repowering a 460 gas w/ a 291 motor.

The oil filter base on the 291 block interferes with the steering shaft. Is there any issue with swapping the old filter base off the 221 block onto the 291 block??
 
(quoted from post at 17:42:33 04/06/09) I am in the process of repowering a 460 gas w/ a 291 motor.

The oil filter base on the 291 block interferes with the steering shaft. Is there any issue with swapping the old filter base off the 221 block onto the 291 block??
Click to expand...

Should fit without any problem. To my knowledge the blocks of that series are all the same and any of the parts will interchange.
 
The early cast iron base and the late aluminum filter bases will not interchange. If you put the early base on you won't have any oil pressure.
 
The early cast iron base and the late aluminum filter bases will not interchange. If you put the early base on you won't have any oil pressure.
 
OK, you have me a little confused. It will fit, bot won't function? Any alternative to my steering shaft routing issue?
 
Check to make sure the holes in the block are in the same position and then use the gasket that fits the filter base.
 
The old cast bas e (from the 221 motor) will bolt right up to it. I have a gasket for the old base and I will bolt this up and give it a try.

I am also converting it to a spin on oil filter too.
 
(quoted from post at 18:04:29 04/10/09) The old cast bas e (from the 221 motor) will bolt right up to it. I have a gasket for the old base and I will bolt this up and give it a try.

I am also converting it to a spin on oil filter too.
Click to expand...

The mounting bolt holes on all the blocks are the same. What you need to look at is to see of the oil holes are in the same locations.
 
You must log in or register to reply here.

Similar threads

B
Oil for IH 460
Replies
12
Views
530
BarnyardEngineering
BarnyardEngineering
3
460 u IH steering
Replies
5
Views
245
fastfarmall
F
J
Ih cyclo planter air pressure issue
Replies
10
Views
336
Joshbraman
J
M
IH 350U cam shaft gear keyway
Replies
5
Views
309
Bob M
Bob M
L
Swapping out cracked case 207 d block, troubles ahead
Replies
12
Views
501
WilBury
WilBury
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top