Author	[Modern View]
dkeav 08-22-2012 09:46:20 50.104.212.155 Report to Moderator	The 900B I drug home has been "modified" a bit. The blocks that go on the rear platform are gone, and some galvinized pipe was welded back in their place. The fender supports have also been cut off and replaced with a piece of angle iron running from each fender. So the platform and fenders are very unstable at this point. I need to cut these upgrades out and return her to stock. Does anyone have a set of the blocks for the rear, if not could someone with an original get some measurements of the blocks and the length of the support braces. I will try to post some pictures of this travesty later. [Reply]   [No Email]
dkeav 08-22-2012 11:14:14 50.104.141.130 Report to Moderator	Re: Fixing 900B platform in reply to dkeav, 08-22-2012 09:46:20   Here is a picture of the mess. This post was edited by dkeav at 11:16:18 08/22/12 2 times. [Reply]  [No Email]
casecollectorsc 08-22-2012 13:04:00 75.102.166.70 Report to Moderator	Re: Fixing 900B platform in reply to dkeav, 08-22-2012 11:14:14   Just proves that some people shouldn't be allowed to have a welder or acy.torch!! [Reply]  [No Email]
dkeav 08-22-2012 13:17:12 50.104.141.130 Report to Moderator	Re: Fixing 900B platform in reply to casecollectorsc, 08-22-2012 13:04:00   Yes, I'm not sure I want to know why they did this, and cut the supports (they bolt on). I just know I have to fix it. [Reply]  [No Email]
Don L. 08-22-2012 10:50:47 99.196.78.48 Report to Moderator	Re: Fixing 900B platform in reply to dkeav, 08-22-2012 09:46:20   parting out a fresh kill 900 diesel today, running with a knock. Don L. [Reply]  [No Email]
dkeav 08-22-2012 11:07:38 50.104.141.130 Report to Moderator	Re: Fixing 900B platform in reply to Don L., 08-22-2012 10:50:47   Don, are the blocks cast? Also if the 900 you are parting has them and you are willing to part ways with them, would you send me a private message please so we can arrange something. [Reply]  [No Email]
Don L. 08-22-2012 13:40:29 99.196.78.48 Report to Moderator	Re: Fixing 900B platform in reply to dkeav, 08-22-2012 11:07:38   Here it is. Bent heavy sheet metal. [Reply]  [No Email]
Ande 08-22-2012 16:26:31 66.231.109.173 Report to Moderator	Re: Fixing 900B platform in reply to Don L., 08-22-2012 13:40:29   Don,do you have a tool box draw for a "900B"? [Reply]  [No Email]
dkeav 08-22-2012 14:27:44 50.104.141.130 Report to Moderator	Re: Fixing 900B platform in reply to Don L., 08-22-2012 13:40:29   Ok, I think I will just fab up some blocks out of rectangular tubing. [Reply]  [No Email]
Don L. 08-22-2012 15:37:34 99.196.78.48 Report to Moderator	Re: Fixing 900B platform in reply to dkeav, 08-22-2012 14:27:44   That should work... The offset is there, for a possible sliding toolbox tray. Don L. [Reply]  [No Email]
dkeav 08-22-2012 20:40:15 98.212.234.220 Report to Moderator	Re: Fixing 900B platform in reply to Don L., 08-22-2012 15:37:34   Quoting Removed, click Modern View to see Don, Wouldn't happen to be selling the drawbar, or entire power steering setup of that 900 you're parting are you? [Reply]  [No Email]
dkeav 08-23-2012 12:32:38 50.104.141.130 Report to Moderator	Re: Fixing 900B platform in reply to dkeav, 08-22-2012 20:40:15   nevermind, I found you on e-bay, will keep an eye out for those. [Reply]  [No Email]
fullpull88 08-22-2012 12:05:30 166.249.133.192 Report to Moderator	Re: Fixing 900B platform in reply to dkeav, 08-22-2012 11:07:38   Some options are only avalible to a farmer with a welder. Big Sal [Reply]  [No Email]