| |
Comments for Welding Basics, Part 2
Add to these Comments
Claude King wrote on Saturday, January 01, 2000 (PST):Welding basic part 3. More on welding alumium and stainless. About wire feed welders, how to weld thin stuff. Is gas needed. coated versus gas not coated
Mike@Ohio wrote on Saturday, January 01, 2000 (PST):Both of the welding articles have all the good basic information for someone to get started welding.
david boothby wrote on Sunday, January 02, 2000 (PST):if your going to weld on a bush hog why not use a 7014 iron powder rod or 7018 which is a low hydroden rod you will get a better weld and both psi on these rods sre 78000. per square inch. the weld will be better strenthened and it will last alot longer through the years 6011 is mostly used on mild steel and for cover passes on black iron pipe welds . before you put a rot pass on them dave b .
E Allison wrote on Monday, January 03, 2000 (PST):Arn't the currents listed for 1/8 inch rod too low (30 to 80 amps). Also, could you supply some pointers to keep from wandering off the desired area when arc welding, this has always been a problem for me. Thanks.
ROBERT GUENTHER wrote on Thursday, January 06, 2000 (PST):I WAS A WELDER FOR 30 YEARS BEFORE RETIRING AND THIS IS ONE OF THE BEST ARTICLES I HAVE READ FOR BEGINING WELDORS.
dan kuzyk (hydraulic dan) wrote on Thursday, January 06, 2000 (PST):I liked your write-up about welding with stick, but I thought that the last number in the welding rod number XXX_ meant the paricular position that it was good for.( I could be wrong about this). I use 6013 welding rod for all mild steel arc welding, and find that it does not stick to the metal as easly as 6011(6013 is probably the easiest rod to use for the beginer to use). I am building a bulldozer from auto parts and I will be selling a set of plans and technical report for it when I am done. I was wondering if the people at yesterdays tractors would like a write-up on basic hydraulics, how to design and build a hydraulic system, (so you can figure out how to build that wierd peice of equipment). I am presently writing this as part of the technical report for the bulldozer built from autoparts. If you want more information on basic hydraulics, or the bulldozer built from auto parts plese E-mail me at hydraulicdan@yahoo.com. thanks dan
Rick R wrote on Thursday, January 06, 2000 (PST):just what i been looking for, someone to explain things about welding I have been welding some stainless and can make a perfect weld flat but when i have to go vertical it is almost impossible sounds like i,m using the wrong rod would like to see more about welding
Johnny Welder wrote on Monday, January 10, 2000 (PST):All-State Welding products makes a No. 34 Smoothcote Extruded Aluminum Electrode for Arc Welding 1/8" and heavier aluminum using DC reverse polarity. It's about $28.00 per lb. What amp. setting is used for this and does it work fairly good? I want to weld 1/8' and 3/16" diamondplate aluminum.
Dennis wrote on Friday, March 16, 2001 (PST):I fell onto the 7014 rod some time ago. I now keep it in stock in every size. It is truly an easy rod to weld with and produces beatiful welds. DC (-) is my setting of choice with this rod. I am planning on modifying the interior of my duck boat but I have no experience welding aluminum. I have both a MIG and STICK welder. Please help me get started.
Don Mahoney wrote on Sunday, July 20, 2003 (PDT):First time I have ever seen any subject explained clearly and simply. Thank you.
Don wrote on Thursday, May 06, 2004 (PDT):I'm confused - I found your article and others on Google while trying to determine the correct rod to use for a project. Another article (see this link) www.jeep-l.net/info_jeep/weld_rod.htm sez the last digit is the type of rod - AC, DC, coating, etc. In your article you state that you're using an AC welder. But if I understand the above info, the rod 6011 is a DC rod..... number 1 being the last number and designator. What is the correct rod for use with an AC welder? Thanks. Don
greg wrote on Tuesday, June 22, 2004 (PDT):thank you very much for providing a in-depth article on BEGINERS welding....it helped me out greatly......
|
Home
| Forums
Today's Featured Article -
Oil Bath Air Filters - by Chris Pratt. Some of us grew up thinking that an air filter was a paper thing that allowed air to pass while trapping dirt particles of a particles of a certain size. What a surprise to open up your first old tractor's air filter case and find a can that appears to be filled with the scrap metal swept from around a machine shop metal lathe. To top that off, you have a cup with oil in it ("why would you want to lubricate your carburetor?"). On closer examination (and some reading in a AC D-14 service manual), I found out that this is a pretty ingenious method of cleaning the air in the tractor's intake tract.
... [Read Article]
Latest Ad:
Super WD9.
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|
|