Talk of the Town:
Repairing a Gas Tank
This interesting discussion is from the Tool Talk Discussion Forum. Remember that
safety is your first priority - make sure you know what you are doing before attempting
a potentially dangerous activity!
The discussion started out with the following post:
I have a leaking gasoline tank on a small
Briggs and Stratton engine. The tank is metal and
is about 4" square by 12" long. The leak is along
I want to try and repair it by heating the tank with
an acetylne torch and laying a bead of solder along
the seam. My torch instructions warn "never use
on any container which has held gasoline" because
of dangerous vapors.
I emptied the tank about a week ago, the cap is off
the top, the valve is out of the bottom, but it
smells like a fuel container and I expect it will
smell for sometime to come.
Do I have anything to worry about heating this thing up?
Any advice appreciated!
What followed are some interesting replies:
It's possible to repair a tank with a torch. The trick is that you first drain it, rinse it out a few times, and then fill it with exhaust gas from your car's muffler. You wouldn't need a acetylene torch, though, a propane torch would work just fine. The trick is to get your surfaces very very clean before you solder.
I just repaired leaks in both a diesel tank as well as a gasoline tank and I'm here writing this!
Advice is FREE. Plastic surgeons aren't.
We've used a 2 part epoxy called Magic Metal to
repair gas and diesel tanks. Clean, (I prefer a good areosol parts cleaner)
then mix and apply. In twenty minutes you can be filling
your tank with fuel instead of that surgeons pocketbook.
Shops which weld automobile gasoline tanks for example, usually steam clean the insides for
more than an hour to ensure that no residual gasoline or oil are emitted from pores in the metal
during heating. Even this is dangerous since there is no way to ensure that all of the volatile
material has been driven from the pores. Additional precautions are taken by others such as
blowing the exhaust from a vehicle into the tank being welded. This has the associated dangers
of carbon monoxide asphyxiation and ignition and explosion of gasoline or other volatile organics
which are contained in the exhaust. According to Part 57.4604, before welding, cutting, or
applying heat with an open flame to pipelines or containers that have contained flammable or
combustible liquids, flammable gases, or explosive solids, the pipelines or containers must be (a)
Drained, ventilated, and thoroughly cleaned of any residue; (b) Vented to prevent pressure
build-up during the application of heat; and (c)(1) Filled with an inert gas or water, where
compatible (venting and other precautions are necessary such as, for example, complete
purging of the air and maintaining a steady stream of nitrogen flowing freely into and out of the
container with the flow rate large enough and outlet hose long enough and of small enough
diameter to eliminate return of air through it); or (2) Determined to be free of flammable gases by
a flammable gas detection device prior to and at frequent intervals during the application of heat.
Bottom line: safest bet for me is to give up on any ideas
about heating a container which previously held fuel.
I've soldered tanks numerous times, and Martin is right. I make it simpler, just wash out the tank with dish soap and hot water, blow interior dry with airhose, and start soldering!!! And start with brite clean metal, and use a soldering paste like NOKORODE etc. Low flame from oxy -acet. or propane is best.
I had a leak in the gas tank of an old Volvo wagon, which I fixed with an epoxy gas tank mender that I got at a parts store. I didn't even drain the tank, just pressed the mender into the leaking seam and smeared it around until the leak stopped. It held for another 6 years and over 120,000 miles. Didn't look pretty, though.
I've used a product called JB Weld to repair the bottom of a gas tank; it should work on a seam as well. It's a two part epoxy and is very easy to use.
After reading all the good advice it appears that this is not an unpopular activity.
You must clean the tank carefully as mentioned before. Then decide if these are the Briggs & Stratton tanks that they glued together, or was it a soldered tank? If it is a glued tank throw it away and look for a replacement. Otherwise solder it with a very fine acetylene flame on bright metal with plenty or flux and the lowest melt solder you can find. One way to assure that all the gas fumes are gone is put your air hose blower in the tank and gently heat the whole tank all over. The gas actually penitrates the metal and especially the joints. Once you've gotten the tank hot to the touch with air blowing inside you are pretty safe. Just remember that Briggs tanks are pretty common and use good sense. I've had tanks WOOF at me even after all precautions were taken. What you're looking to do is avoid catistrophic explosion.
Keep your fingers.
This information was gathered at
the Tool Talk Discussion
|Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a Company you can trust and have generous return policies! Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ]|
| Copyright © 1997-2013 Yesterday's Tractor Co.|
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
|About this site - Yesterday's Tractors is your one-stop source for antique tractors. If you are interested in older tractors you've come to the right place! Join more than 275,000 other classic tractor enthusiasts from all over the globe. We have many resources for antique tractor enthusiasts available including photos, classified ads, more than 24 tractor discussion forums, a show guide, values, specs and much more. Bookmark this site and come back often. Thanks for stopping by! Feel free to use our feedback form to send us your comments, suggestions and ideas.|