Earthmaster Project Progress
by Steve Watroba
Just a little update on my Earthmaster......it's back from the dead! I pulled
the head, and soaked the stuck valves with mystery oil overnight, re-installed
the head, and bingo, the compression returned. But alas, my carb foiled me
again, it would fire a second then flood out. After numerous dead ends for a
replacement carb, I went to work fixing mine.I soldered new floats on the
float arm, they came from an old motorcycle carb, replaced the packing on the
throttle shaft with o-rings, cut new gaskets, and cleaned, cleaned, cleaned.
It worked! I could not believe the original head gasket does not leak.The
first tank of fuel is treated with the mentioned Marvel mystery oil, I hope to
keep those valves clean.
A note about the valves, only the intakes were stuck, my theory when my carb
was giveing me trouble, I had to keep the choke half closed to keep it
running, this made the mixture way too rich, this gummed up the valves, after the
tractor sat a while the valve were stuck.
Since rebuilding the carb, things were better(it started), the first couple
days I had to keep the choke closed to keep it running, but the longer I've
been running it the better it runs! Yesterday it was running strong with the
choke wide open! I've almost gone through the first 5 gallons of treated
fuel, I think this is whats helping things improve. I've been pulling
logs, clearing my house lot on the familly estate. I get a lot of looks from
the nieghbors, and comments about how they are impressed this old thing still
runs so well.
I still want a good carb, the main problem with mine is the mixture screw was
rotted out, and stripped, I turned a point on a regular machine screw, and
jammed it in there.This is another reason why it may run too rich.
Lastly, a word about Earthmaster carbs. In my various research on this
tractor, or it's continental motor, I've been surprised to find how many carb
#'s I've been given by dealers, suppliers, tractor tests on MH Ponys (which use
the same engine), etc. At last
count the following carbs are supposed to work on this tractor, none of wich
I've been able to find reasonably priced: Marvel schubler TSV13, TSV16, TSV24,
Zenith 14993, and the latest from a past "Tractor of the Month" article, Zenith 61S5.
My email is firstname.lastname@example.org, let me know if you have info about
these carbs, pics of these carbs, or carbs available.Thanks.
|Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a Company you can trust and have generous return policies! Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ]|
| Copyright © 1997-2013 Yesterday's Tractor Co.|
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
|About this site - Yesterday's Tractors is your one-stop source for antique tractors. If you are interested in older tractors you've come to the right place! Join more than 275,000 other classic tractor enthusiasts from all over the globe. We have many resources for antique tractor enthusiasts available including photos, classified ads, more than 24 tractor discussion forums, a show guide, values, specs and much more. Bookmark this site and come back often. Thanks for stopping by! Feel free to use our feedback form to send us your comments, suggestions and ideas.|